I want to introduct something about Two Port Voice Gateway. Two Port Voice Gateway function description: The popularization of the Internet drives the rapid development of a wide variety of IP-based applications. The IP telephone technology has become the major means for operators to develop voice services now. Especially, IP technology becomes the core of the next generation network (NGN), so the IP-based voice technology will keep soaring speeding the future and become the No. 1 choice of new operators in exploring services. Upon the market requirement, Zhuhai Estone Co., Ltd has launched the IAD 2FXS gateway integrated access device. As an Integrated Access Device, the upstream port of the IAD can be directly connected to the IP network and its downstream port can be connected to multiple ordinary telephone sets, to provide basic accesses for POTS users. This user port gateway can support two telephone lines and connect multiple telephone sets. At the same time, this device is capable of Internet gateway and can access data stream, such as Email or Internet in
A current loop describes two different electrical signalling schemes.
Digital
For digital serial communications a current loop is a communication interface that uses current instead of voltage for signaling. Current loops can be used over moderately long distances (tens of kilometres), and can be interfaced with optically isolated links.
Long before the RS-232 standard, current loops were used to send digital data in serial form for teleprinters. More than two teletypes could be connected on a single circuit allowing a simple form of networking. Older teletypes used a 60 mA current loop. Later machines, such as the ASR33 teleprinter, operated on a lower 20 mA current level and most early minicomputers featured a 20 mA current loop interface, with an RS-232 port generally available as a more expensive option. The original IBM PC serial port card had provisions for a 20 mA current loop. A digital current loop uses the absence of current for high (space or break), and the presence of current in the loop for low (mark).
The maximum resistance for a current loop is limited by the available voltage. Current loop interfaces usually use voltages much higher than those found on an RS 232 interface, and cannot be interconnected with voltage-type inputs without some form of level translator circuit.
MIDI (Musical Instrument Digital Interface) is a digital current loop interface.
Analog
Analog current loops are used where a device must be monitored or controlled remotely over a pair of conductors. Only one current level can be present at any time.
Given its analog nature, current loops are easier to understand and debug than more complicated digital fieldbuses, requiring only a handheld digital multimeter in most situations. Using fieldbuses and solving related problems usually requires much more education and understanding than required by simple current loop systems.
Additional digital communication to the device can be added to current loop using HART Protocol. Digital process buses such as FOUNDATION Fieldbus and Profibus may replace analog current loops.
Process-control use
For industrial process control instruments, analog 4-20 mA and 10-50 mA current loops are commonly used for analog signaling, with 4 mA representing the lowest end of the range and 20 mA the highest. The key advantages of the current loop are that the accuracy of the signal is not affected by voltage drop in the interconnecting wiring, and that the loop can supply operating power to the device. Even if there is significant electrical resistance in the line, the current loop transmitter will maintain the proper current, up to its maximum voltage capability. The live-zero represented by 4 mA allows the receiving instrument to detect some failures of the loop, and also allows transmitter devices to be powered by the same current loop (called two-wire transmitters). Such instruments are used to measure pressure, temperature, flow, pH or other process variables. A current loop can also be used to control a valve positioner or other output actuator. An analog current loop can be converted to a voltage input with a precision resistor. Since input terminals of instruments may have one side of the current loop input tied to the chassis ground (earth), analog isolators may be required when connecting several instruments in series.
Depending on the source of current for the loop, devices may be classified as active (supplying power) or passive (relying on loop power). For example, a chart recorder may provide loop power to a pressure transmitter. The pressure transmitter modulates the current on the loop to send the signal to the strip chart recorder, but does not in itself supply power to the loop and so is passive. ( A 4-wire instrument has a power supply input separate from the current loop.) Another loop may contain two passive chart recorders, a passive pressure transmitter, and a 24 V battery. (The battery is the active device).
Panel mount displays and chart recorders are commonly termed ‘indicator devices’ or ‘process monitors’. Several passive indicator devices may be connected in series, but a loop must have only one transmitter device and only one power source (active device).
The relationship between current value and process variable measurement is set by calibration, which assigns different ranges of engineering units to the span between 4 and 20 mA. The mapping between engineering units and current can be inverted, so that 4 mA represents the maximum and 20 mA the minimum.
Long circuits
Analog current loops were occasionally carried between buildings by dry pairs in telephone cables leased from the local…(and so on) To get More information , you can visit some products about wholesale st adapter, Automatic Voltage Regulator, . The Two Port Voice Gateway products should be show more here!
About the Author:
himfr can provide you most popular hot products from china!
Article Source: ArticlesBase.com – Current loop
1935 Finnish Business Men’s Outing – Quincy, MA
